barginbin
18,11,07, 18:22
http://www.maggotdrowning.com/pole/b.jpgSo you've made the first step and bought a new pole but what do you do with it now?Poles do not come ready elasticated unless it is part of the deal or you can manage to wangle the shop owner to elasticate it for you, but this can also work out expensive especially if you've got a few top kits as part of the package.
Added to that the task of elastication is a lot easier than it at first sounds and you'll get that satisfaction of knowing that you've done it and with the materials of your choice.
So what do you need, here's a list:
http://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gifJunior hacksawhttp://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gifFine sand paper (600 grit wet and dry)http://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gifScissorshttp://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gifStanley Knife or similar
http://www.maggotdrowning.com/pole/a.jpgFirst things first, choose a clean, spacious area to work, there's nothing worse than trying to step around everything and this will only lead to disaster.Lay all your top sections out on a flat surface and decide what grades of elastic you need.
A guide to this is:
http://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gif 4 - 8 Small fish such as Roach, Rudd, Skimmershttp://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gif 8 -12 Medium sized fish and small Carphttp://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gif12-14 Carp up to 10lb in snag free watershttp://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gif14- 20 Big Carp and snaggy watersMake sure you also check your Pole rating first - Don't exceed it's maximum rating otherwise damage will occur
http://www.maggotdrowning.com/pole/c.jpgNext, go buy all your bits if you haven't done so alreadyFor this you'll need:
http://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gifElastics - there are many types available so ask around for other opinions and recommendationshttp://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gifBungs - winder bungs are best because it gives you a few optionshttp://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gifBushes - Internal or External? External gives you more flexibility and requires less cutting back of the top kitshttp://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gifConnectors - Again several choices available or use a 'Crows Foot' and dispense with the connector
http://www.maggotdrowning.com/pole/1.jpgHere we go....Take a Bush and offer it side on to your pole top section and try and locate where the section diameter equals the internal diameter of the bush
Mark this point with a pencil
(Tip: Use the same size bushes for all tops based upon the largest you'll need)
http://www.maggotdrowning.com/pole/2.jpgNext using the Junior Hacksaw, gently pull the hacksaw blade backwards over the line to cut using the hacksaw's own weight to apply pressure - Do not push down or force it or you will split the carbon.At the same time slowly rotate the section and you'll find that you'll cut a nice, neat groove into it.
Keep doing so until you have removed the part you don't need
http://www.maggotdrowning.com/pole/3.jpgTry the Bush for size and if it's not a nice, tight fit, remove another 2 centimetres until it ishttp://www.maggotdrowning.com/pole/4.jpgAfter that and your nerves are now calming down, gently clean the face of the cut with the Sand Paper to achieve a square face with no sharp edgeshttp://www.maggotdrowning.com/pole/5.jpgNext, put the remaining sections together with the first and mark them all and repeat the above steps so that the sections are all cut to the same length.Sand the faces, push on your Bushes and that's the first step over
http://www.maggotdrowning.com/pole/6.jpgThere you have it, your tops all cut to the same length and ready for the elastichttp://www.maggotdrowning.com/pole/7.jpgNext step is to trim the Winder to the correct size...Take your next section and push it into one of the top kits to see how far it goes in. Make a note of how far it goes in, you'll need to know this later
http://www.maggotdrowning.com/pole/8.jpgWinder at the ready...http://www.maggotdrowning.com/pole/9.jpgPlace it into the top of your next section so that it sits in without pushing ithttp://www.maggotdrowning.com/pole/10.jpgMark the point where it meets the pole with a pencil, remove it and cut at this point.
You now need to put it into your top section and gently push it in just beyond the point where you previously made a note of.If it doesn't go far enough in, don't force it, trim a little more off until it fits just right
(Tip: Remember you can always take some off, but you can't put it back on)
http://www.maggotdrowning.com/pole/11.jpgNow for the ElasticThis will show you how to tie a 'Crows Foot' instead of using a plastic connector
Firstly, form a loop and tie a double figure eight loop knot...
http://www.maggotdrowning.com/pole/12.jpgWet the elastic and pull tight to close the knot...http://www.maggotdrowning.com/pole/13.jpgSo your knot looks like thishttp://www.maggotdrowning.com/pole/14.jpgThen cut across the loop and trim the loose end to 1centimetre. The result being a Crows Foothttp://www.maggotdrowning.com/pole/15.jpgRemove the bush and thread this on your elastic first making sure you have it the right way round, then slide the elastic into the top of your section, right the way through, and out of the end.Once you've got to the end push the Bush back into place
http://www.maggotdrowning.com/pole/16.jpgWhen the elastic is out of the other end, tie a figure eight loop into it, close to the end of the pole...http://www.maggotdrowning.com/pole/17.jpg..as suchhttp://www.maggotdrowning.com/pole/18.jpgPlace this onto your Winder bung and wind on a few coils until you have tension, then guide it into the polehttp://www.maggotdrowning.com/pole/19.jpgAt this stage it's best to stretch the elastic from the tip end until you have pulled it out to it's limit.Release it slowly and then go back to the Winder Bung and re-tension it to remove any slack
Job done, now the Pole Cup.....
http://www.maggotdrowning.com/pole/20.jpgTo fit a Pole Cup again lay your Cupping Kit alongside your top sections as you'll need to cut it back so that they are the same lengthhttp://www.maggotdrowning.com/pole/21.jpgMake allowances for the length of the cup when doing so and don't forget you'll need a tight fit.To get this offer the cup up against the top section and mark on the Cupping Kit the position of the connector; you need to ensure that the middle of the cup is level with the end of your pole top sections
Cut the Cupping Kit with the Junior Hacksaw as earlier and push the connector on.
If it is too tight a fit, don't force it but drill the connector to make it slightly larger. Some Pole Cups come with different sized connectors
http://www.maggotdrowning.com/pole/22.jpgFinished, the Cupping Kit should now be the same length as your top sections and this will ensure accurate feeding http://www.maggotdrowning.com/pole/23.jpgFinished job...http://www.maggotdrowning.com/pole/24.jpg... Grab a coffee
Added to that the task of elastication is a lot easier than it at first sounds and you'll get that satisfaction of knowing that you've done it and with the materials of your choice.
So what do you need, here's a list:
http://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gifJunior hacksawhttp://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gifFine sand paper (600 grit wet and dry)http://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gifScissorshttp://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gifStanley Knife or similar
http://www.maggotdrowning.com/pole/a.jpgFirst things first, choose a clean, spacious area to work, there's nothing worse than trying to step around everything and this will only lead to disaster.Lay all your top sections out on a flat surface and decide what grades of elastic you need.
A guide to this is:
http://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gif 4 - 8 Small fish such as Roach, Rudd, Skimmershttp://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gif 8 -12 Medium sized fish and small Carphttp://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gif12-14 Carp up to 10lb in snag free watershttp://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gif14- 20 Big Carp and snaggy watersMake sure you also check your Pole rating first - Don't exceed it's maximum rating otherwise damage will occur
http://www.maggotdrowning.com/pole/c.jpgNext, go buy all your bits if you haven't done so alreadyFor this you'll need:
http://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gifElastics - there are many types available so ask around for other opinions and recommendationshttp://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gifBungs - winder bungs are best because it gives you a few optionshttp://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gifBushes - Internal or External? External gives you more flexibility and requires less cutting back of the top kitshttp://www.maggotdrowning.com/_themes/copy-of-blends/blebul1a.gifConnectors - Again several choices available or use a 'Crows Foot' and dispense with the connector
http://www.maggotdrowning.com/pole/1.jpgHere we go....Take a Bush and offer it side on to your pole top section and try and locate where the section diameter equals the internal diameter of the bush
Mark this point with a pencil
(Tip: Use the same size bushes for all tops based upon the largest you'll need)
http://www.maggotdrowning.com/pole/2.jpgNext using the Junior Hacksaw, gently pull the hacksaw blade backwards over the line to cut using the hacksaw's own weight to apply pressure - Do not push down or force it or you will split the carbon.At the same time slowly rotate the section and you'll find that you'll cut a nice, neat groove into it.
Keep doing so until you have removed the part you don't need
http://www.maggotdrowning.com/pole/3.jpgTry the Bush for size and if it's not a nice, tight fit, remove another 2 centimetres until it ishttp://www.maggotdrowning.com/pole/4.jpgAfter that and your nerves are now calming down, gently clean the face of the cut with the Sand Paper to achieve a square face with no sharp edgeshttp://www.maggotdrowning.com/pole/5.jpgNext, put the remaining sections together with the first and mark them all and repeat the above steps so that the sections are all cut to the same length.Sand the faces, push on your Bushes and that's the first step over
http://www.maggotdrowning.com/pole/6.jpgThere you have it, your tops all cut to the same length and ready for the elastichttp://www.maggotdrowning.com/pole/7.jpgNext step is to trim the Winder to the correct size...Take your next section and push it into one of the top kits to see how far it goes in. Make a note of how far it goes in, you'll need to know this later
http://www.maggotdrowning.com/pole/8.jpgWinder at the ready...http://www.maggotdrowning.com/pole/9.jpgPlace it into the top of your next section so that it sits in without pushing ithttp://www.maggotdrowning.com/pole/10.jpgMark the point where it meets the pole with a pencil, remove it and cut at this point.
You now need to put it into your top section and gently push it in just beyond the point where you previously made a note of.If it doesn't go far enough in, don't force it, trim a little more off until it fits just right
(Tip: Remember you can always take some off, but you can't put it back on)
http://www.maggotdrowning.com/pole/11.jpgNow for the ElasticThis will show you how to tie a 'Crows Foot' instead of using a plastic connector
Firstly, form a loop and tie a double figure eight loop knot...
http://www.maggotdrowning.com/pole/12.jpgWet the elastic and pull tight to close the knot...http://www.maggotdrowning.com/pole/13.jpgSo your knot looks like thishttp://www.maggotdrowning.com/pole/14.jpgThen cut across the loop and trim the loose end to 1centimetre. The result being a Crows Foothttp://www.maggotdrowning.com/pole/15.jpgRemove the bush and thread this on your elastic first making sure you have it the right way round, then slide the elastic into the top of your section, right the way through, and out of the end.Once you've got to the end push the Bush back into place
http://www.maggotdrowning.com/pole/16.jpgWhen the elastic is out of the other end, tie a figure eight loop into it, close to the end of the pole...http://www.maggotdrowning.com/pole/17.jpg..as suchhttp://www.maggotdrowning.com/pole/18.jpgPlace this onto your Winder bung and wind on a few coils until you have tension, then guide it into the polehttp://www.maggotdrowning.com/pole/19.jpgAt this stage it's best to stretch the elastic from the tip end until you have pulled it out to it's limit.Release it slowly and then go back to the Winder Bung and re-tension it to remove any slack
Job done, now the Pole Cup.....
http://www.maggotdrowning.com/pole/20.jpgTo fit a Pole Cup again lay your Cupping Kit alongside your top sections as you'll need to cut it back so that they are the same lengthhttp://www.maggotdrowning.com/pole/21.jpgMake allowances for the length of the cup when doing so and don't forget you'll need a tight fit.To get this offer the cup up against the top section and mark on the Cupping Kit the position of the connector; you need to ensure that the middle of the cup is level with the end of your pole top sections
Cut the Cupping Kit with the Junior Hacksaw as earlier and push the connector on.
If it is too tight a fit, don't force it but drill the connector to make it slightly larger. Some Pole Cups come with different sized connectors
http://www.maggotdrowning.com/pole/22.jpgFinished, the Cupping Kit should now be the same length as your top sections and this will ensure accurate feeding http://www.maggotdrowning.com/pole/23.jpgFinished job...http://www.maggotdrowning.com/pole/24.jpg... Grab a coffee